My 3C exhibits similar behavior in one of my ‘s if I ramp up the BUS Clock and the configuration tool will either not detect it or permanently damage the card. Now the next problem is trying to get an IP address, which it won’t do. Users browsing this forum: Well unfortunately, I can’t seem to find the option to turn down the BUS clock to see if that would make any difference at all. Return to General Old Hardware. Just won’t freaking get an IP address from the router.
|Date Added:||21 February 2004|
|File Size:||37.49 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
Testing the loop back ehher16 trying another ISA slot is a good idea eher16. Unfortunately, I couldn’t get very far to installing the utility software as it doesn’t detect the card, even in Windows and DOS with the packet driver successfully installed.
You do not have the required permissions to view the files attached to this post. Also do you have another card you can use? It appears that even though MPU on the SB16 is set at and is disabled, the Ether16 still complains and doesn’t initialize.
Strange, given it is an NE clone. Though just to be sure, I’ll see if I can try it on one of my systems another time. PM me if you have some to give away.
Linksys LNE – Ether16 Combo LAN Card Driver – TechSpot
Check you have the linksyys resources set Windows always gets my network cards IRQ wrong on a fresh install but if you believed windows everything is fine. Well unfortunately, I can’t seem to find the option to turn down the BUS clock to see if that would make any difference at all. Another thing you could try is dropping to dos or even test it in a dos system using a suitable packet driver and see if you can get it to connect using the mTCP suite of apps.
Still can’t connect to ethee16 network. This disclaimer is brought to you thanks to the BSA.
Linksys LNE2000 – Ether16 Combo LAN Card
Caluser Yes, that’s the exact card that I’m using. Still couldn’t get an IP address from the router and couldn’t do a loopback that way. My 3C exhibits similar behavior in one of my ‘s if I ramp up the BUS Clock and the configuration tool will either not detect it or permanently damage the card. Setting it manually to what I know is correct gives me a warning about changing resources but everything works suddenly I’m not familiar with that particular card but I’m guessing the driver disk has a setup program where you assign IRQ plus less important stuff like frame type, etc or try another PCI slot and hope plug and play assigns it another one.
There is no material that is knowingly illegal here.
I ended up replacing it with a PCI card and permanently installing it into the where it had no problem and is actually a good card, also ran the other one in a for years before putting a PCI one in only because I had no spare ISA Ethernet cards for a non-PCI system I was messing with.
I’m beginning to think that it could be some sort of resource conflict, even though Windows doesn’t suspect it and that the SB16 is not even using it. Can you try the Card and Tool in another PC. Have linosys SB16 and Yamaha sound card installed alongside. Board index All times are UTC.
This site hosts no abandonware. Last edited by Caluser on Is this the card? That’s linkssys a good sign then that the card is not detected.
Just use the NE I was able to do a loopback with no problems at all. I Can’t help wondering if it could be a clock dependency of some sort – i. If you are lucky, the network card will have jumpers, otherwise it a case of trial and error to find the IRQ and IO base settings. In addition, it also does have a tendency to not even initialize properly under Windows in some cases whenever I make hardware changes to the system and NOT even touch the network card at all.
Or maybe, recove all other Cards you dont need for Dos and try Setup again. Unrelated but it’s probably a good time to mention there was a Winsock update for Windows 95 as well- http: Looking for vintage computers and parts.